Optical Fiber Waveguides | NOTES | ECETOTAL

 Table of Contents

• Electromagnetic Spectrum
• Optical Fiber Waveguides
• Multimode graded-index fiber
• Single-mode fiber 

Electromagnetic Spectrum

The radio waves and light are electromagnetic waves. The rate at which they alternate in polarity is called their frequency (f) measured in hertz (Hz). The speed of the electromagnetic wave (c) in free space is approximately 3 x 10^8 m/sec. The distance travelled during each cycle is called  wavelength (λ) In fiber optics, it is more convenient to use the wavelength of light instead of the frequency with light frequencies; wavelength is often stated in microns or nanometers.

Electromagnetic Spectrum

1 micron (µ) = 1 Micrometre (1 x 10^-6 meter) 

1 nano (n) = 10^-9 meter 

Fiber optics uses visible and infrared light. Infrared light covers a fairly wide range of wavelengths and is generally used for all fiber optic communications. Visible light is normally used for very short range transmission using a plastic fiber.

Optical Fiber Waveguides

In free space light ravels as its maximum possible speed i.e. 3 x 10^8 m/s. When light travels through a material it exhibits certain behaviour explained by laws of reflection, refraction.

An optical waveguide is a structure that "guides" a light wave by constraining it to travel along a certain desired path. If the transverse dimensions of the guide are much larger than the wavelength of the guided light, then we can explain how the optical waveguide works using geometrical optics and total internal reflection.

A waveguide traps light by surrounding a guiding region, called the core, made from a material with an index of refraction n_core, with a material called the cladding, made from a material with an index of refraction n_cladding < n_core. Light entering is trapped as long as,   sinθ > n_cladding/n_core.

Light can be guided by planar or rectangular waveguides, or by optical fibers. An optical fiber consists of three concentric elements, the core, the cladding and the outer coating, often called the buffer. The core is usually made of glass or plastic. The core is the light-carrying portion of the fiber. The cladding surrounds the core. The cladding is made of a material with a slightly lower index of refraction than the core. This difference in the indices causes total internal reflection to occur at the core-cladding boundary along the length of the fiber. Light is transmitted down the fiber and does not escape through the sides of the fiber.

• Fiber Optic Core: The inner light-carrying member with a high index of refraction.
• Cladding: The middle layer, which serves to confine the light to the core. It has a lower index of refraction.
• Buffer: The outer layer, which serves as a "shock absorber" to protect the core and cladding from damage. The coating usually comprises one or more coats of plastic material to protect the fiber from the physical environment. Sometimes metallic sheaths are added to the coating for further physical protection.
• Light injected into the fiber optic core and striking the core-to-cladding interface at an angle greater than the critical angle is reflected back into the core. Since the angles of incidence and reflection are equal, the light ray continues to zigzag down the length of the fiber. The light is trapped within the core. Light striking the interface at less than the critical angle passes into the cladding and is lost.
• Fibers for which the refractive index of the core is a constant and the index changes abruptly at the core-cladding interface are called step-index fibers. Step-index fibers are available with core diameters of 100 mm to 1000 mm. They are well suited to applications requiring high-power densities, such as delivering laser power for medical and industrial applications.

• Light injected into the fiber optic core and striking the core-to-cladding interface at an angle greater than the critical angle is reflected back into the core. Since the angles of incidence and reflection are equal, the light ray continues to zigzag down the length of the fiber. The light is trapped within the core. Light striking the interface at less than the critical angle passes into the cladding and is lost.

Multimode graded-index fiber

• Fibers for which the refractive index of the core is a constant and the index changes abruptly at the core-cladding interface are called step-index fibers. Step-index fibers are available with core diameters of 100 mm to 1000 mm. They are well suited to applications requiring high-power densities, such as delivering laser power for medical and industrial applications.

• Multimode step-index fibers trap light with many different entrance angles, each mode in a step-index multimode fiber is associated with a different entrance angle. Each mode, therefore, travels along a different path through the fiber. Different propagating modes have different velocities. As an optical pulse travels down a multimode fiber, the pulse begins to spread. Pulses that enter well separated from each other will eventually overlap each other. This limits the distance over which the fiber can transport data. Multimode step-index fibers are not well suited for data transport and communications.
• In a multimode graded-index fiber the core has an index of refraction that decreases as the radial distance from the centre of the core increases. As a result, the light travels faster near the edge of the core than near the center. Different modes, therefore, travel in curved paths with nearly equal travel times. This greatly reduces the spreading of optical pulses.

Single-mode Fiber

• A single-mode fiber only allows light to propagate down its centre and there are no longer different velocities for different modes. Single-mode fiber is much thinner than a multimode fiber and can no longer be analyzed using geometrical optics. Typical core diameters are between 5 mm and 10 mm.
• When laser light is coupled into a fiber, the distribution of the light emerging from the other end reveals if the fiber is a multimode or single-mode fiber.

Light emerging from multimode fiber & single-mode fiber

Optical fibers are used widely in the medical field for diagnoses and treatment. Optical fibers can be bundled into flexible strands, which can be inserted into blood vessels, lungs and other parts of the body. An Endoscope is a medical tool carrying two bundles of optic fibers inside one long tube. One bundle directs light at the tissue being tested, while the other bundle carries light reflected from the tissue, producing a detailed image. Endoscopes can be designed to look at regions of the human body, such as the knees, or other joints in the body.

ALSO, READ Signal Distortion in Optical Fibers

ALSO, READ OFC : Introduction